How to Clean Ninja Blender 2021


Ninja blenders need no introduction as the company has been making high-quality, efficient, and powerful blenders for decades. A ninja blender makes your household task more manageable and hassle-free. But the issue pops up when you want to clean it. If you don’t know how to clean ninja blender, the cleaning job can be a hassle and may take a lot of time.

Is Regular Cleaning Essential For Ninja Blenders?

Regular cleaning is essential to ensure optimal performance. Additional maintenance is required as it is a long-term and practical kitchenware. Taking care of the kitchen appliance from time to time will ensure its efficiency and keep it hygienic. In fact, experts suggest cleaning them after every blending session to ensure the best state.

If you have recently purchased a Ninja blender, you might be asking yourself what the best method to clean a ninja blender is. In this post, we will share some creative tips to clean ninja blenders.

How to Clean Ninja Blender in an Appropriate Way?

When you take a little bit extra care to clean your ninja blender, you ensure its best state and long service life. Probably, you have received an instruction manual with the blender that tells you how to clean ninja blender. However, you still need to consider some other things to clean the blender properly.

Things You Need To Clean a Ninja Blender

  • A sponge or dishcloth
  • Non-toxic liquid soap
  • Baking soda (non-mandatory)
  • Lemon (non-mandatory)
  • Vinegar (non-mandatory)

Things You Should Do Before Cleaning

  • Make sure to remove the power cable from the power source prior to cleaning the blender.
  • Probably, a lot of germs and bacteria have already accumulated in different blender parts. Take apart all the possible parts of the blender to clean it properly.
  • You may see some marks on the container if you have been making bulletproof coffee.
  • Take everything out from the blender; Taking apart the blades is also possible by twisting it from the below part of the jar.

Start With the Blender Container

It is best to start with the blender jar as all the food items are blended inside it. The jar may become unhygienic due to left-over foods. Hence, it is vital to prioritize clean the main pot and then move to other blender parts.

Here are instructions on how to wash your blender container:

Step 1—Use Mild Liquid Soap to Blend

Load the ninja blender container with slightly warm water and go half of it. Next, add few drops of mild liquid soap and turn on the blender in low settings. Run the blender for 1-2 minutes and take out the foamy solution. After that, load the blender with slightly warm water to make it fully clean.

Step 2—Use Lemon to Take Off Hard Spots

Lemon is an effective solution to remove different tough stains from blender jars. Fill the ninja blender jar with slightly warm water; pour few drops of mild liquid soap and few pieces of chopped lemon. Turn on the blender at low speeds and run it for 1-2 minutes. Then, pour out the foamy solution and rinse it with slightly warm water.

Step 3—Use a Dishcloth to Scrub the Container

Once you completed the two steps, use a dishcloth or a tough sponge to clean the inner part of the jar precisely. Use a small amount of water and few drops of liquid soap to clean the pot. Keep rubbing the jar until all the stains go away. Additionally, make sure you also scrub the outer part of the container. Rinse it on the running water to clean.

How to Get Rid Of the Toughest Stains?

Are you still facing difficulty in cleaning some stubborn stains? Then, you can use a half cup of baking soda and one cup of white vinegar, along with mild dish soap and lukewarm water.

Again, close the lid and run the blender for several minutes until the foamy solution touches the top. Keep the sudsy solution inside the jar for 3-4 hours, and then rinse the pot properly with running water. Use mild liquid soap and lukewarm water if you notice any uncomfortable smell.

How to Clean Ninja Blender?

Step 1—Disassemble the blades and wash it

First of all, you need to take out the blades from the jar and use mild liquid soap to clean the blades. You can use a tough sponge to get off the hard marks. Use some white vinegar to make the blade edge shiny and sustain the original look.

Step 2— Use Denture Cleaning Tablets to remove excessive dirt

When you use your blender for several months without cleaning blades properly, it may become too dirty. In that case, you can use denture cleaning tablets for a deep clean as they have antibacterial properties.

Take a mid-sized bowl, fill it up with lukewarm water, and add two denture cleaning tablets to it. Keep them on the bowl for 1-1.5 hours and clean them properly with a sponge afterward.

Cleaning and Lubricating the Gasket Latch

While cleaning the jar blades, make sure you clean the gasket latch. Use mild liquid soap and lukewarm water to clean them appropriately. Make sure it doesn’t have any build-up of food residue or any dirt. After that, use seed oil or any vegetable oil to lubricate the gasket latch.

Dry Up the Blender Container and Additional Accessories

After cleaning all the blender parts, it is time to air-dry them. Make sure you don’t put together all the blender parts until they become dehydrated.

How to clean the blender motor part?

Take a dish towel and soak them in warm, soapy water. Now, make the towel damp by squeezing it. Use the damp towel to clean the blender motor part and its base. Avoid cleaning it aggressively. Besides, make sure you clean all the surrounding areas of the control surface with Q-tip as they are pretty challenging to clean.


Hopefully, you have already learned how to clean ninja blender effectively in this easy-proven way. Isn’t it easy to clean a ninja blender when you have the perfect cleaning accessories and methods? It is best to clean the ninja blender each time you use it to sustain a long lifespan and its performance.

If you are looking for the best affordable and power-efficient ninja blender, don’t forget to click here.

Leave a Comment